Brownells UK - World's Largest Supplier of Gun Parts, Gunsmith Tools & Shooting Accessories United Kingdom

RCBS
TUNGSTEN COATED NECK SIZING BUSHING

076683817006 100060346
No-Lube-Required Bushings for Use With GMM Sizing Dies
RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
31.9 35.9 27 GBP
Product no.: 100060346
RCBS 0.185" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81700 076683817006 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .185

Top takeaways

  1. RCBS Tungsten Coated Neck Sizing Bushings provide precise bullet tension without case lube, due to Tungsten Disulfide coating.
  2. Designed for use with RCBS Gold Medal Match neck sizing dies, ensuring proper case neck alignment and consistent shooting.
  3. To select the correct bushing size, subtract .002"-.003" from the loaded cartridge's outside neck diameter or calculate based on neck wall thickness and bullet diameter.

Attributes

Diameter (in): .185 Delivery weight: 0.045kg

Item details

Made in USA



Product no.: 100060360
RCBS 0.199" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81714 076683817143 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
32.9 GBP 1 £32.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .199
Product no.: 100060362
RCBS 0.201" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81716 076683817167 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
33.9 GBP 1 £33.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .201
Product no.: 100060363
RCBS 0.202" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81717 076683817174 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
33.9 GBP 1 £33.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .202
Product no.: 100060364
RCBS 0.203" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81718 076683817181 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
33.9 GBP 1 £33.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .203
Product no.: 100060365
RCBS 0.204" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81719 076683817198 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
33.9 GBP 1 £33.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .204
Product no.: 100060366
RCBS 0.205" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81720 076683817204 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
32.9 GBP 1 £32.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .205
Product no.: 100060367
RCBS 0.206" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81721 076683817211 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
31.9 GBP 1 £31.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .206
Product no.: 100060370
RCBS 0.210" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81725 076683817259 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
32.9 GBP 1 £32.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .210
Product no.: 100060371
RCBS 0.211" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81726 076683817266 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
32.9 GBP 1 £32.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .211
Product no.: 100060372
RCBS 0.212" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81727 076683817273 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
32.9 GBP 1 £32.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .212
Product no.: 100060376
RCBS 0.217" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81732 076683817327 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
32.9 GBP 1 £32.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .217
Product no.: 100060377
RCBS 0.218" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81733 076683817334 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
32.9 GBP 1 £32.90 *
Delivery time approx. 7-14 days.
1 pcs. in the USA warehouse
Specs: Diameter (in): .218
Product no.: 100060379
RCBS 0.220" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81735 076683817358 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
35.9 GBP 0 £35.90 *
Notify on availability
Out of stock. No ETA.
Specs: Diameter (in): .220
Product no.: 100060469
RCBS 0.353" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81868 076683818683 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
35.9 GBP 0 £35.90 *
Notify on availability
Out of stock. No ETA.
Specs: Diameter (in): .353
Product no.: 100060349
RCBS 0.188" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81703 076683817037 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .188
Product no.: 100060353
RCBS 0.192" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81707 076683817075 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .192
Product no.: 100060356
RCBS 0.195" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81710 076683817105 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .195
Product no.: 100060357
RCBS 0.196" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81711 076683817112 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .196
Product no.: 100060359
RCBS 0.198" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81713 076683817136 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .198
Product no.: 100060368
RCBS 0.207" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81722 076683817228 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .207
Product no.: 100060373
RCBS 0.214" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81729 076683817297 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .214
Product no.: 100060374
RCBS 0.215" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81730 076683817303 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .215
Product no.: 100060383
RCBS 0.225" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81740 076683817402 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .225
Product no.: 100060406
RCBS 0.258" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81773 076683817730 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .258
Product no.: 100060451
RCBS 0.324" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81839 076683818393 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .324
Product no.: 100060470
RCBS 0.354" TUNGSTEN NECK SIZING BUSHING
Mfr Part: 81869 076683818690 RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
Notify on availability
Not available.
Specs: Diameter (in): .354

🎯 Achieve perfect bullet tension with the RCBS 0.185' Tungsten Neck Sizing Bushing. Ideal for reloaders using Gold Medal dies. Shop now for precision! 🔧🔩

No-Lube-Required Bushings for Use With GMM Sizing Dies
RCBS Coated Neck Bushings are interchangeable to let the reloader select a bushing that gives precisely the right amount of tension on the bullet when using RCBS Gold Medal Match neck sizing dies. These bushings have a Tungsten Disulfide (WS2) anti-friction coating, so they do not require use to traditional case lube. Self-centering for proper alignment with case neck For best results, use of high-end brass with consistent neck thicknesses For use ONLY with RCBS Gold Medal neck sizing dies RCBS recommends having neck bushings one to two sizes above and below your target diameter (see note below). RCBS Coated Neck Bushings are a small but critical component in loading extremely consistent-shooting ammo with your Gold Medal Match sizing dies. Brownells Gun Tech™ Tip: There are two ways to select the steel neck bushings you need: (1) Measure the outside neck diameter of your loaded cartridge and subtract .002" to .003". This allows approximately .001" of brass to spring back for correct neck tension. (2) You can also measure the neck wall thickness of your case, multiply by two, add the diameter of your bullet and subtract .002" to .003".
In stock
£18.90 * £16.90 - £18.90*
0
In stock
£19.90 * £19.90 - £29.90*
0
Newsletter