Furnished with a complete set of adapters and spacers for installation on 12 gauge Mossberg 500, Maverick 88, Remington 870, and Winchester 1200/1300 pump shotguns. Easy to install, requires no modifications to firearm. Formed steel with elongated cooling slots protects your hands from burns. Provides a secure, non-slip, grasping surface, plus maximum heat dissipation. Simply slide over barrel and secure with supplied hardware. Black oxide finish matches most shotgun finishes. No gunsmithing required to fit most popular 12 gauge pump guns.
SPECS: Steel, black oxide, matte finish. 13¾ (35cm) long.
More...
Customer ratings for ADVANCED TECHNOLOGY HEAT SHIELD
Number of ratings: 8
From brownells.com: 6
Average rating: 3.4
How to avoid scratches(19/10/2019)
Further to my review about it simply not fitting some people said it scratched the barrel. There are some punched dimples along it that will scratch your barrel as that part makes contact. Put a small bead of clear plumbing silicone on the dimples and let it fully set then fit it. This will act as a rubber buffer and wont mark the barrel. You cant see it and silicone withstands 1000 °C so it wont burn or smoke. That's why it's also used to seal car mufflers. Job done
Looks nice but simply does not fit a 500A(19/10/2019)
Can't fault Brownells as the item was shipped in good time. This heat shield looks really nice but it simply doesn't fit. Its the perfect size and radius for the barrel but dont try to fit it tight up to the receiver. The last half an inch of barrel near the breech is simply wider than the shield. Fits perfectly half an inch forward. I asked ATI for help and basically a guy called Troy fobbed me off and said that's what it's supposed to look like. Customer service 1 /10 for ATI but if you dont mind it slightly forward it's great
Solid Piece of Gear(16/09/2009)
Installed the Heat Shield on my Rem 870 in about 10 minutes and it fit with no alterations to the shield or the shotgun. Well constructed with an excellent pattern for heat dispersion. I would buy it again.
IVE BOUGHT A FEW OF THESE(13/04/2010)
IF YOU SHOOT A LOT OF SHELLS AND HAVE EVER BURNED YOUR HAND BY ACCIDENTALLY TOUCHING THE BARREL THIS ITEM IS FOR YOU. IT INSTALLS EASILY AND QUICKLY AND DOESN'T NEED TO BE REMOVED WHEN YOU CLEAN THE BORE OR BREAK DOWN YOUR SHOTGUN. IT ALSO ADDS A TOUGH LOOK TO THE SHOTGUN. IVE ONLY INSTALLED THIS ON MOSSBERG 500'S AND HAVE HAD NO PROBLEMS.
Difficult to install(21/01/2011)
Quality parts and manufacturing, but tricky to install on my 870 Tactical. Took some extra bending of the middle tabs and widening of the receiver-end of the shield to fit snug around my barrel. Had to file down the upper inside edge of the fore-end, as well, as the middle tabs were grinding on it upon cycling the action.
SHS-1300 Heat Shield by Advanced Technol(12/08/2011)
its plastic it belongs on my suns toy gun not on a tactical home protection shot gun, When i picked up my shot gun after i had installed the heat shield,the back of the heat shield came off of my shot gun due to the ring on the back of the heat shield is not a solid ring and it is flimsy and moves around on my shot gun. I do not recommend this product if you are serious about home defense or self protection. i recommend one made of steel.
1300 defender(05/03/2012)
*this may not apply to all shotguns* The fit and finish of the product is unacceptable. During install the heat shield heavily scratches the barrel's finish. The receiver end of the shield does not grip the barrel well allowing it to move and produce wear on the barrel. The forward end, with the two screw holes, comes to you flared out and out of alignment. This neccesitates a lot of test fits and alterations which again damages the finish of the gun. A gunsmith might have better luck with it. Mine found its way into the dumpster.
A good buy(25/01/2014)
This was an easy install, it is not a custom piece built specific to any gun, it is built to fit every 870 ever made. Take your time and you won't damage the finish on your weapon or on the heat shield. The instructions are pretty clear and easily followed (I read them afterwards) no modification was required to my weapon (H&R Pardner Protector Pump) even though I installed an 870 wood stock and forearm and a +2 magazine extension. The heat shield does require a little patience for a good tight fit but looks good after installation. It is a great deal for quality and looks, especially because it it metal and cost the same as some synthetic models
Product no.: 019000004 ADVANCED TECHNOLOGY HEAT SHIELD Mfr Part: SHS1300758152513007 Furnished with a complete set of adapters and spacers for installation on 12 gauge Mossberg 500, Maverick 88, Remington 870, and Winchester 1200/1300 pump shotguns. Easy to install, requires no modifications to firearm. Formed steel with elongated cooling slots protects your hands from burns. Provides a secure, non-slip, grasping surface, plus maximum heat dissipation. Simply slide over barrel and secure with supplied hardware. Black oxide finish matches most shotgun finishes. No gunsmithing required to fit most popular 12 gauge pump guns.
43.9GBP21£43.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Compatible with 12 gauge Mossberg 500, Maverick 88, Remington 870, and Winchester 1200/1300 shotguns, the HEAT SHIELD is easy to install without firearm modifications.
Designed for hand protection, the shield has elongated cooling slots for heat dissipation and provides a non-slip surface for better grip.
Constructed from steel with a black oxide finish to match most shotguns, it measures 13¾ inches and comes with all necessary hardware for installation.
🔥 Upgrade your shotgun with the Advanced Technology HEAT SHIELD! Fits Mossberg 500, Remington 870 & more. Easy installation, no gunsmithing needed. Shop now! 🛡️
Furnished with a complete set of adapters and spacers for installation on 12 gauge Mossberg 500, Maverick 88, Remington 870, and Winchester 1200/1300 pump shotguns. Easy to install, requires no modifications to firearm. Formed steel with elongated cooling slots protects your hands from burns. Provides a secure, non-slip, grasping surface, plus maximum heat dissipation. Simply slide over barrel and secure with supplied hardware. Black oxide finish matches most shotgun finishes. No gunsmithing required to fit most popular 12 gauge pump guns.
SPECS: Steel, black oxide, matte finish. 13¾ (35cm) long.
More...
Customer ratings for ADVANCED TECHNOLOGY HEAT SHIELD
Number of ratings: 8
From brownells.com: 6
Average rating: 3.4
How to avoid scratches(19/10/2019)
Further to my review about it simply not fitting some people said it scratched the barrel. There are some punched dimples along it that will scratch your barrel as that part makes contact. Put a small bead of clear plumbing silicone on the dimples and let it fully set then fit it. This will act as a rubber buffer and wont mark the barrel. You cant see it and silicone withstands 1000 °C so it wont burn or smoke. That's why it's also used to seal car mufflers. Job done
Looks nice but simply does not fit a 500A(19/10/2019)
Can't fault Brownells as the item was shipped in good time. This heat shield looks really nice but it simply doesn't fit. Its the perfect size and radius for the barrel but dont try to fit it tight up to the receiver. The last half an inch of barrel near the breech is simply wider than the shield. Fits perfectly half an inch forward. I asked ATI for help and basically a guy called Troy fobbed me off and said that's what it's supposed to look like. Customer service 1 /10 for ATI but if you dont mind it slightly forward it's great
Solid Piece of Gear(16/09/2009)
Installed the Heat Shield on my Rem 870 in about 10 minutes and it fit with no alterations to the shield or the shotgun. Well constructed with an excellent pattern for heat dispersion. I would buy it again.
IVE BOUGHT A FEW OF THESE(13/04/2010)
IF YOU SHOOT A LOT OF SHELLS AND HAVE EVER BURNED YOUR HAND BY ACCIDENTALLY TOUCHING THE BARREL THIS ITEM IS FOR YOU. IT INSTALLS EASILY AND QUICKLY AND DOESN'T NEED TO BE REMOVED WHEN YOU CLEAN THE BORE OR BREAK DOWN YOUR SHOTGUN. IT ALSO ADDS A TOUGH LOOK TO THE SHOTGUN. IVE ONLY INSTALLED THIS ON MOSSBERG 500'S AND HAVE HAD NO PROBLEMS.
Difficult to install(21/01/2011)
Quality parts and manufacturing, but tricky to install on my 870 Tactical. Took some extra bending of the middle tabs and widening of the receiver-end of the shield to fit snug around my barrel. Had to file down the upper inside edge of the fore-end, as well, as the middle tabs were grinding on it upon cycling the action.
SHS-1300 Heat Shield by Advanced Technol(12/08/2011)
its plastic it belongs on my suns toy gun not on a tactical home protection shot gun, When i picked up my shot gun after i had installed the heat shield,the back of the heat shield came off of my shot gun due to the ring on the back of the heat shield is not a solid ring and it is flimsy and moves around on my shot gun. I do not recommend this product if you are serious about home defense or self protection. i recommend one made of steel.
1300 defender(05/03/2012)
*this may not apply to all shotguns* The fit and finish of the product is unacceptable. During install the heat shield heavily scratches the barrel's finish. The receiver end of the shield does not grip the barrel well allowing it to move and produce wear on the barrel. The forward end, with the two screw holes, comes to you flared out and out of alignment. This neccesitates a lot of test fits and alterations which again damages the finish of the gun. A gunsmith might have better luck with it. Mine found its way into the dumpster.
A good buy(25/01/2014)
This was an easy install, it is not a custom piece built specific to any gun, it is built to fit every 870 ever made. Take your time and you won't damage the finish on your weapon or on the heat shield. The instructions are pretty clear and easily followed (I read them afterwards) no modification was required to my weapon (H&R Pardner Protector Pump) even though I installed an 870 wood stock and forearm and a +2 magazine extension. The heat shield does require a little patience for a good tight fit but looks good after installation. It is a great deal for quality and looks, especially because it it metal and cost the same as some synthetic models