Absolutely Essential For Accurate, Safe, Chamber Work
The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
SPECS: Machined Steel. Size varies with caliber and gauge style. NOTE: Gauges Interchangeable between calibers have same Stock #. .30/30 Cartridges are .219 Wasp, .219 Zipper, .22 Sav HP, .30-30, .32 Win Spl, .32-40, .375 Win and .38-55. .30/06 Cartridges are .25-06, 6.5mm-06, .270 Win, .30-06, 8mm-06, .338-06 and .35 Whelen. Magnum Cartridges are .257 Weatherby, .264 Win, 6.5 Rem Mag, .270 Weatherby, .275 H&H, 7mm Rem Mag, 7mm Weatherby, 7x61 S&H, .300 H&H, .300 Win Mag, .30-338, .300 Weatherby, .308 Norma, 8mm Mag, .338 Win, .340 Weatherby, .350 Rem Mag, .357 Norma, .375 H&H, .416 Rem Mag and .458 Win.
More...
Customer ratings for CLYMER 30-30 WINCHESTER NO-GO GAUGE
Number of ratings: 6
From brownells.com: 6
Average rating: 4.8
Good Gauge(09/03/2017)
Good Gauge, Good Value. The identification on the gauge is not easily readable, but it should be kept in its well labeled case like any precision gauge.
Safety First(09/03/2017)
I purchase this Gauge after trying to locate a gunsmith near where I lived and worked to check the head space on my AR build. It was cheaper than a 2-3 hour drive and it work as it was designed.
Works(30/03/2017)
Works as advertized.
I used this to check Colt SAA 1st Gen(14/07/2018)
1st Gen Colt SAA checked out OK with this gauge. Works as advertised. Had to remove cylinder to get the gauge out, since it would not rotate into recoil plate.
I have to give it a good review because it's my fault. The extractor on my mosin nagant 91/30 absolutely won't budge. The go works fine but the no go obviously won't seat correctly without the removal of the extractor. Both (go and no go) look like fine tools but I can't rate them so much as I can say you DON'T have to remove the firing pin you DO have to remove the extractor so make sure you can do that before ordering them.
Works as advertised(03/07/2012)
The gentleman who wrote the 1st review: You must remove the extractor. So make sure you have a replacement for the part the extractor is in. I broke mine trying to get it out. Instead of removing the extractor, I cut a slot in the gauge for the extractor to pass over. Then you don't have to worry about it.
Product no.: 184100219 CLYMER 221 REMINGTON FIREBALL NO-GO GAUGE Mfr Part: NG221REM The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184100221 CLYMER 22 LONG RIFLE NO-GO GAUGE Mfr Part: NG22LR The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
48.9GBP17£48.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Specs:Cartridge: 22 Long Rifle, 22 Short, 22 Long, 22 Bentz, 22 MatchStyle: No Go Gauge
Product no.: 184100223 CLYMER 6MM BR NO-GO GAUGE Mfr Part: NGBR The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184100241 CLYMER 223 REMINGTON NO-GO GAUGE Mfr Part: NG223REM The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
48.9GBP17£48.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Specs:Cartridge: 223 Remington, 6 mm x 45Style: No Go Gauge
Product no.: 184100266 CLYMER 300 SAVAGE NO-GO GAUGE Mfr Part: NG300SAV The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184100307 CLYMER 300 REMINGTON ULTRA MAGNUM NO-GO GAUGE Mfr Part: NG300REMUMAG The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
59.9GBP20£59.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Specs:Cartridge: 300 Remington Ultra Magnum, 7 mm Remington Ultra Magnum, 375 Remington Ultra MagnumStyle: No Go Gauge
Product no.: 184100311 CLYMER 30-06 SPRINGFIELD NO-GO GAUGE Mfr Part: NG3006SPR The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184100321 CLYMER BELTED MAGNUM NO-GO GAUGE Mfr Part: NGBLT The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
48.9GBP16£48.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Specs:Cartridge: 300 Winchester Magnum, 375 H&H Magnum, 350 Remington MagStyle: No Go Gauge
Product no.: 184100341 CLYMER 9MM LUGER NO-GO GAUGE Mfr Part: NG9MMLUG The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
48.9GBP13£48.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Product no.: 184100351 CLYMER 30 M1 CARBINE NO-GO GAUGE Mfr Part: NG30M1 The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
48.9GBP22£48.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Product no.: 184100361 CLYMER 25-20 WINCHESTER NO-GO GAUGE Mfr Part: NG2520 The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
48.9GBP19£48.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Specs:Cartridge: 218 Bee, 25-20 Winchester, 32-20 Winchester, 218 Mashburn BeeStyle: No Go Gauge
Product no.: 184100381 CLYMER 357 MAGNUM NO-GO GAUGE Mfr Part: NG357MGN The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184100391 CLYMER 38 SUPER NO-GO GAUGE Mfr Part: NG38SUPN The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
48.9GBP12£48.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Product no.: 184100451 CLYMER 45 ACP NO-GO GAUGE Mfr Part: NG45ACP The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184110121 CLYMER 12 GAUGE NO-GO GAUGE Mfr Part: NG12 The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
64.9GBP36£64.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Product no.: 184110201 CLYMER 20 GAUGE NO-GO GAUGE Mfr Part: NG20 The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 100011311 CLYMER 300 AAC BLACKOUT NO-GO GAUGE Mfr Part: NG300BLACK The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
48.9GBP23£48.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Specs:Cartridge: 300 AAC BlackoutStyle: No Go Gauge
Product no.: 184000078 CLYMER 224 VALYRIE NO-GO GAUGE Mfr Part: NG224VALK The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
48.9GBP16£48.90
*
Delivery time approx. 7-14 days. More than 10 pieces in USA warehouse
Product no.: 184000080 CLYMER 6.5MM CREEDMOOR NO-GO GAUGE Mfr Part: NG65CREED The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184100264 CLYMER 300 WSM NO-GO GAUGE Mfr Part: NG300WSM The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Specs:Cartridge: 300 WSM (Winchester Short Mag), 270 WSM (Winchester Short Mag), 338 Winchester Magnum, 325 WSM (Winchester Short Mag)Style: No Go Gauge
Product no.: 184100331 CLYMER 45-70 GOVERNMENT NO-GO GAUGE Mfr Part: NG4570GOVT The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184100491 CLYMER 7.62X39MM NO-GO GAUGE Mfr Part: NG76239 The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184000036 CLYMER 5.56X45MM NATO NO-GO GAUGE Mfr Part: NG556NATO The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184100236 CLYMER 22 HORNET NO-GO GAUGE Mfr Part: NG22HOR The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184100256 CLYMER 250 SAVAGE NO-GO GAUGE Mfr Part: NG250SAV The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
Product no.: 184100511 CLYMER 45 LONG COLT NO-GO GAUGE Mfr Part: NG45LC The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
🎯 Ensure your 30-30 Winchester rifle's safety with Clymer No-Go Headspace Gauges! 🛠️ Precision machined for accuracy. Get started on proper maintenance now! 🔍
Absolutely Essential For Accurate, Safe, Chamber Work
The only way to accurately measure and test the length of the chamber of the rifle. Essential when chambering a new barrel to ensure a tight, accurate, safe chamber. Whenever you buy a used gun, always check the headspace before firing. Gauges are etched with “Go” or “No-Go” and caliber/gauge name for easy identification. Both Forster and Clymer gauges are made to SAAMI specs.
SPECS: Machined Steel. Size varies with caliber and gauge style. NOTE: Gauges Interchangeable between calibers have same Stock #. .30/30 Cartridges are .219 Wasp, .219 Zipper, .22 Sav HP, .30-30, .32 Win Spl, .32-40, .375 Win and .38-55. .30/06 Cartridges are .25-06, 6.5mm-06, .270 Win, .30-06, 8mm-06, .338-06 and .35 Whelen. Magnum Cartridges are .257 Weatherby, .264 Win, 6.5 Rem Mag, .270 Weatherby, .275 H&H, 7mm Rem Mag, 7mm Weatherby, 7x61 S&H, .300 H&H, .300 Win Mag, .30-338, .300 Weatherby, .308 Norma, 8mm Mag, .338 Win, .340 Weatherby, .350 Rem Mag, .357 Norma, .375 H&H, .416 Rem Mag and .458 Win.
More...
Customer ratings for CLYMER 30-30 WINCHESTER NO-GO GAUGE
Number of ratings: 6
From brownells.com: 6
Average rating: 4.8
Good Gauge(09/03/2017)
Good Gauge, Good Value. The identification on the gauge is not easily readable, but it should be kept in its well labeled case like any precision gauge.
Safety First(09/03/2017)
I purchase this Gauge after trying to locate a gunsmith near where I lived and worked to check the head space on my AR build. It was cheaper than a 2-3 hour drive and it work as it was designed.
Works(30/03/2017)
Works as advertized.
I used this to check Colt SAA 1st Gen(14/07/2018)
1st Gen Colt SAA checked out OK with this gauge. Works as advertised. Had to remove cylinder to get the gauge out, since it would not rotate into recoil plate.
I have to give it a good review because it's my fault. The extractor on my mosin nagant 91/30 absolutely won't budge. The go works fine but the no go obviously won't seat correctly without the removal of the extractor. Both (go and no go) look like fine tools but I can't rate them so much as I can say you DON'T have to remove the firing pin you DO have to remove the extractor so make sure you can do that before ordering them.
Works as advertised(03/07/2012)
The gentleman who wrote the 1st review: You must remove the extractor. So make sure you have a replacement for the part the extractor is in. I broke mine trying to get it out. Instead of removing the extractor, I cut a slot in the gauge for the extractor to pass over. Then you don't have to worry about it.